loading

 Expert in Water Quality Measurement and Water Treatment Project Since 2007

How to Measure Sulfuric Acid Concentration ?

How to Measure Sulfuric Acid Concentration ?

The on-line continuous measurement of sulphuric acid/oleum is based on the fact that a physical property will change as the concentration changes.  Properties such as conductivity, refractive index and sound velocity are typically used to measure sulphuric acid/oleum concentrations.  The recommended methods of measurement over the whole range of sulphuric acid and oleum are given below.

ModelSJ2083C Acid and Alkali Concentration Meter
H2SO4  Sulphuric Acid(92~100.00)%

H2SO4 Sulphuric Acid

(0~25.00)%;
Sensor typeInductive Conductivity Sensor

Electrical conductivity is a property of a fluid that can be used to determine its concentration.  The graph below shows the conductivity (micromhos) at 25ºC for several different fluids, including sulphuric acid from 0 to 100%wt.  The vertical axis ranges from 0 to 900,000 micromhos.For sulphuric acid, the conductivity varies such that for a given conductivity there could be more than one concentration.  This makes conductivity unsuitable for measurement over the full range of acid concentration (i.e. 0 to 100% H2SO4).  However, conductivity can be used where the concentration will vary over a small range and where the range will not cross over one of the peaks or valleys of the conductivity curve.Below shows the correlation between conductivity and concentration for four common solutions

How to Measure Sulfuric Acid Concentration ? 1

Conductivity measurement is a reliable indicator of the concentration of most acid or base solutions. The desired chemical concentration is achieved using a two stage mixing procedure. During the first stage, the flow ratio control unit on the missing tank is set to provide (x) gallon per minute of the full strength solution and (y) gallons per minute of water. These values are adjusted to produce a concentration value which is slightly weaker than the desired value. This ratio control must include alarm capabilities to indicate "low flow" conditions for both the full strength solution and the water in order to prevent wasted chemicals or hazardous situations. 

How to Measure Sulfuric Acid Concentration ? 2

SJG-2083C Acid and Alkali Concentration Meter

At the second stage, a conductivity sensor and analyzer function as a "trim control". This combination adds small amounts of full-strength solution to the mixing tank to produce the exact concentration desired. For example, to produce a 4% caustic solution from a large bulk caustic supply at 50%, the flow ratio controller is adjusted to make a 3% solution and the conductivity information is used to add additional caustic to achieve the 4% concentration.Conductivity is a very reliable index of the concentration for most acid and base (caustic) solutions. Because the DDG-2080C Acid and base Concentration Meter works with DDG-GY  Inductive conductivity sensor ,it is virtually maintenance free; it is the first choice for any application.

How to Measure Sulfuric Acid Concentration ? 3

               

Acid and Alkali Concentration Meter
How to Measure Sulfuric Acid Concentration ? 4

               

Inductive Conductivity Sensor with Flow-cell
How to Measure Sulfuric Acid Concentration ? 5

               

Inductive Conductivity Sensor for Pipe install

prev
Cooling Tower Water Treatment
Top 10 Global Companies of Wastewater Treatment and Water Quality Analysis
next
recommended for you
no data
Get in touch with us

Contact Us

Contact Person:Michael Luo
E-MAIL:michael@shboqu.com
Tel:86-021-20965230
Fax:86-021-20981909
Skype:+86-15000087545
Whatsapp:86-15000087545
Office Add:No. 118 Xiuyan Road,Pudong New Area,Shanghai,Zip Code:201315,China

Contact us right away

BOQU Instrument focus on development and production of water quality analyzers and sensors, including water quality meter, dissolved oxygen meter, pH sensors, etc.

Copyright © 2024 Shanghai BOQU Instrument Co.,Ltd | Sitemap
Customer service
detect